Father's Day Card Tutorial

Make this Boat Card for your dad by following this tutorial
Father's Day Card You will need:

Carmine ProMarker
Berry ProMarker
Coral ProMarker
Gold ProMarker
Meadow Green ProMarker
Apple Green ProMarker
Royal Blue ProMarker
Rubdown Transfer 'Memories' - silver
Im-packs background Images Set 2
StudioTac A5 Sheets
StudioTac Super
Ivory Colour Card Set
Bleedproof Paper
X-acto Knife
White Card
Metal Rule
Hole Punch
Blue Ribbon
Card Step-by-Step:

Colour in the card with the Meadow Green Marker.

Cut a piece of bleedproof paper 10.5cm x 6cm and colour in the piece with the Carmine Marker. Using the rule and the chisel-nib end of the Berry Marker draw lines down and across the greeting card at equal spacing. Repeat using the bullet-nib end of the ProMarker offset from the previous thicker lines.

Cut a second piece of paper 10.5cm x 1.7cm, draw circles across the middles of the strip and colour in the area outside with the Apple ProMarker leaving the circles white.

Adhere the Carmine Chequered paper at the bottom of the card using the StudioTac A5 sheets. Next adhere the Apple strip above, and draw â€Ëœstitchesâ€â„¢ using the Royal Blue Marker
Label Step-by-Step:

Cut a label shape from a piece of card 7cm x 12cm. Print the water image from the Im-packs Background Images CD, cut two sections 7cm wide, one 2.5 cm high and one 4.5cm high with a wave pattern at the top of each.

Next, take a piece of bleedproof paper and, with a rule, mark lines with the chisel and bullet-nib ends of the Apple ProMarker to create a chequer-board pattern. Cut a section 7cm x 3cm high with a wave pattern at the top. Adhere the wave images and Apple Chequered pieces to the label using StudioTac.

On another piece of card draw a boat shape with the Royal Blue ProMarker, decorate and cut-out.

Use the hole punch to punch a hole at the top of the label. With the Royal Blue Marker run the nib around the edges of the punched hole, label and waves. Draw a circle indented from the punched hole and colour in the space with the Meadow Green Marker. Then, stick the boat to the label using StudioTac Super.

Take the blue ribbon and tie a bow at the top of the label. Finally, burnish your chosen phrases to the label and adhere the label to the card using StudioTac Super.

Make this Chequered Card for your dad by following this tutorial
Father's Day Card You will need:

Gold Metallic ProMarker
Pastel Green ProMarker
China Blue ProMarker
Cyan ProMarker
Henna ProMarker
Rubdown Transfer â€ËœMemoriesâ€â„¢ - black
Im-packs background Images Set 1
Ivory Colour Card Set
Bleedproof Paper
White Card
X-acto Knife
StudioTac Super
Metal Rule
Hole Punch
Brown and blue Ribbon
Card Step-by-Step:

Colour in the card with the Pastel Green Marker. Using the rule and the chisel-nib end of the Cyan Marker draw lines down and across the greeting card at equal spacing. Repeat using the bullet-nib end of the China Blue ProMarker offset from the previous Cyan lines, and again using the Gold Metallic ProMarker bullet-nib.

Next, print out the image of the rustic, blue painted wood and stick to the top of the greeting card using StudioTac. Then colour a strip of card 1cm deep with the China Blue ProMarker and use the Gold Metallic Marker to decorate with a dot pattern. Stick this strip across the card using StudioTac Super.
Label Step-by-Step:

Cut a label shape from a piece of card 4.4cm x 7.4cm and colour with the China Blue ProMarker. Then cut another piece of card to the same shape but this time 3.7cm x 6.7cm, use the Gold Metallic ProMarker to colour in this piece. Use the chisel end of the Henna ProMarker to add the aged-edging look and adhere to the larger Blue label using StudioTac Super.

Cut a small square of the printed background paper 3xcm x3cm and stick in the middle of the label using StudioTac Super. Next, cut a piece of card 2.5cm x 2.5cm (slightly narrower at the top) colour in Gold, and add the Henna edging as before. Burnish â€ËœDadâ€â„¢ from the â€ËœMemoriesâ€â„¢ Rubdown Transfer sheet and adhere the square to the label with StudioTac Super.

Use the hole punch to punch a hole at the top of the label, and tie a bow with the ribbon. Tear off a small section of StudioTac Super from the roll and press to the centre of the back of the label, press the label to the greeting card.